100A to 200A main service panel upgrades
New 200A meter main or panel, grounding and bonding brought to current code, and the PG&E application handled for overhead and underground services.
Read about panel upgradesFacing home insurance non-renewal because of knob and tube in Alameda or Contra Costa County? We provide certified inspection letters and turnkey replacement. How the insurance letter works
Ally Electric & Solar is a family-owned Richmond electrical contractor, upgrading East Bay homes to modern 200A service since 2002. We handle the permit, the PG&E coordination and the city inspection.
Most requested: panel upgrades in Oakland, panel upgrades in Berkeley, panel upgrades in Richmond
Three answers, then a planning timeline for your city.
Your timeline appears here once all three are answered.
New 200A meter main or panel, grounding and bonding brought to current code, and the PG&E application handled for overhead and underground services.
Read about panel upgradesFull rewiring that works around lath and plaster, plus a written compliance letter your insurance underwriter can accept.
Read about knob & tube removalSpan and other load-managing panels that can let a home add an EV charger or heat pump without a full service upgrade, when the load calculation supports it.
Read about smart panelsSafe generator hookups for PG&E shutoffs and outdoor emergency disconnects for homes in Orinda, Moraga, Kensington and the Oakland and Berkeley hills.
Read about generator transfer switchesReplacement of Federal Pacific Stab-Lok and Zinsco panels, brands with well-documented breaker problems that many insurers and home inspectors flag.
Read about fpe & zinsco replacementHome electrification means safer wiring, lower-maintenance appliances and a house ready for solar and an EV. It almost always starts at the electrical panel.
An old panel doesn't fail quietly. It warns you first.
A heat pump moves heat. It doesn't burn anything to make it.
No open flame in the kitchen. No combustion fumes in the house.
Upgrade the panel once, and every electric project after it gets easier.
Every city permits differently. Pick your area to see what we usually find in its homes.
Much of Oakland's flatland housing went up between 1900 and 1930, and many of those craftsman and colonial revival homes still run on 60A or 100A service, with original knob and tube in the walls above the lath and plaster.
Permits: City of Oakland Planning & Building Department
Berkeley's brown-shingle and craftsman homes are some of the oldest in the East Bay. Original fuse boxes, ungrounded circuits and knob and tube are common, and lath-and-plaster walls make careful fishing of new wire the difference between a clean job and a patching project.
Permits: City of Berkeley Permit Service Center
Albany's compact 1920s to 1940s bungalows frequently have the meter and panel on a tight side setback, which shapes where a new 200A meter main can go and how PG&E routes the service drop.
Permits: City of Albany Community Development Department
Piedmont's large homes from the 1910s through the 1930s often hide knob and tube behind fine plaster and woodwork, and many still run on service far smaller than the house now needs.
Permits: City of Piedmont Building Division
Emeryville is mostly lofts and newer housing, but its Triangle neighborhood still has small early-1900s homes, some with original wiring and very small service.
Permits: City of Emeryville Building Division
Alameda has one of the largest collections of Victorian homes in the Bay Area. Many still have knob and tube, fuse panels or service far too small for modern loads.
Permits: City of Alameda Permit Center
Richmond mixes early-1900s homes in Point Richmond with large stocks of 1940s wartime housing. Both commonly arrive with undersized service, and the older homes add knob and tube to the scope.
Permits: City of Richmond Planning & Building Services
El Cerrito's hillside homes from the 1930s through the 1950s often have the original panel low on a garage wall or under the house, with service sized for a home that never planned on an EV, a heat pump or a hot tub.
Permits: City of El Cerrito Building Division
Kensington is unincorporated, so permits run through Contra Costa County rather than a city hall. Its 1920s to 1950s hillside homes often have long service runs and panels in tight basement spaces.
Permits: Contra Costa County Department of Conservation and Development
San Pablo is surrounded by Richmond, and much of its housing went up in the 1940s and 1950s for wartime and postwar workers. Those small homes often still run on 60A or 100A service sized for a much simpler kitchen.
Permits: City of San Pablo Building Division
Pinole mixes a small historic Old Town with neighborhoods built mostly from the 1950s through the 1980s. Many of those homes have original panels, including Federal Pacific and Zinsco models, that predate today's electrical loads.
Permits: City of Pinole Building Division
Most of Hercules was built from the 1970s onward, so knob and tube is rare. The common projects here are electrification ones: EV chargers, heat pumps and solar that push a 100A or 125A service past its limit.
Permits: City of Hercules Building Division
El Sobrante is unincorporated, so permits come from Contra Costa County rather than a city. Its homes range from older valley houses to hillside homes from the 1950s through the 1970s, many on original service.
Permits: Contra Costa County Department of Conservation and Development
Moraga's ranch homes from the 1950s through the 1970s were wired for a different era of load. Pools, EV chargers and whole-home heat pumps push many of them past 100A or 125A service.
Permits: Contra Costa County Building Inspection (for the Town of Moraga)
Orinda's homes range from 1930s cottages to large mid-century hillside houses. Long driveways and underground laterals are common, and older homes still carry original wiring in the oldest parts of the house.
Permits: Contra Costa County Building Inspection (for the City of Orinda)
Lafayette's homes are mostly from the 1940s through the 1970s, many on large lots with pools, spas and additions that have outgrown the original 100A or 125A service.
Permits: Contra Costa County Building Inspection (for the City of Lafayette)
Walnut Creek's neighborhoods were mostly built from the 1950s through the 1970s. Ranch homes from that era commonly have Federal Pacific or Zinsco panels and 100A service.
Permits: City of Walnut Creek Building Division
Much of San Leandro was built in the 1940s and 1950s, and many of those homes still have their original 60A or 100A service, ungrounded circuits and small panels.
Permits: City of San Leandro Building and Safety Services
Castro Valley is unincorporated, so permits come from Alameda County. Its homes range from older valley houses to hillside neighborhoods built from the 1960s through the 1990s.
Permits: Alameda County Community Development Agency (unincorporated area)
We measure what the home draws today and what it will draw after EVs, heat pumps or remodels, and size the service to match.
We pull the permit and file the PG&E application, then coordinate the disconnect date for overhead or underground service.
New meter main or panel, service entrance, and grounding and bonding brought to current code, usually in one working day.
We meet the inspector, get the green tag, and PG&E restores power to the new service.
Family-owned in Richmond since 2002
Electrical work since 2002 and solar since 2010, from the same family.
California C-10 license #806465
Verify it any time on the Contractors State License Board site.
$2M general liability
Certificate of insurance available on request before work starts.
First-inspection guarantee
If your work doesn't pass the first city inspection, we fix it and schedule the re-inspection at no cost.
Insurers in California increasingly decline or non-renew homes with active knob and tube wiring. We inspect the home and give you a written letter describing what's there. Once we remove it, we issue a completion letter with the finaled permit, which is what most underwriters ask for to reinstate or write a new policy.
It depends on whether your service is overhead or underground and whether PG&E needs to change anything on their side. A straightforward overhead upgrade usually moves in weeks; underground services or transformer work can take longer. We submit the PG&E application early and coordinate the disconnect and reconnect so you're without power for one day of work.
The main cost drivers are whether the panel stays in place or moves, overhead versus underground service, grounding and bonding corrections, and whether stucco, siding or drywall needs opening. We give a fixed written price after a free site visit, including permit and PG&E coordination.
Not always. A load calculation under the electrical code shows what your existing service can carry. If you're close, a load-managing smart panel or circuit-level load management can let you add the new equipment without upgrading the service.
We fish new wire through existing cavities, attics and crawl spaces and open plaster only where we must, with small, planned access holes. We'll tell you in advance where openings will be and how they'll be patched.